how to enable internet connection sharing on windows 7 ??

Cookies are disabled

Guide to Network and Sharing Center in Windows 7, 8, 10
How to Use the Windows 10 Camera App. December 21st, by Aseem Kishore File in: Connect to the ad hoc network you created. You receive the following message: For example, if you connect to the Internet by using a modem, right-click the connection that you want under Dial-up. Next to Connections , you can click on the name of the WiFi or Ethernet network to bring up the status info dialog for the current connection. You must have at least two different network adapters installed to use internet connection sharing.

Private or Public Network

{{search404Captions.content404Title}}

If you're trying to share your internet connection with multiple devices at your house, you may be wondering how to do it without complicated networking. Luckily, your Windows or Mac computer can easily share its internet connection with the rest of the network. You can even turn your computer into a wireless access point so you don't need a router to connect your wireless devices.

Computer Networking Internet Access. Configure your devices on the network. When sharing internet through your network, it will require a slightly different layout than a standard network. The basic layout is as follows: If you are connecting a modem to the host computer via Ethernet, it will need two Ethernet ports one to connect to the modem, and the other to connect to the hub or router.

Connect the host computer to the WAN port of a wired hub or wireless router using an Ethernet cable. Connect the other computers to the hub or router using Ethernet or a wireless signal.

Note that the connecting computers don't need any special settings, and can be running any operating system. If you're just connecting two computers, connect them directly via Ethernet. Open the Network Connections window on the host computer. Right-click on the adapter that is connected to the internet source. This could be your modem or your USB hotspot. Make sure that you are only performing these steps on the adapter that is actually connected to the internet, not the adapter that will be connecting the host to the rest of the network.

Select "Properties" and click the. Check the "Allow other network users to connect through this computer's Internet connection" box. Click Apply to save your changes. At this point, you can turn your host computer into a wireless access point if you have an unused wireless adapter. Click here for instructions. This is important if the other computers need to access email, FTP, or other special services.

Check the box for each service that you want to enable. Open your wireless router's configuration page. Now that the host computer is set up, you'll need to configure the router to allow it to pass the connection through. Click here for detailed instructions on opening the router's configuration page. If you're using a hub or switch, you won't need to perform any additional configuration. Open the Internet Settings page on the router. The exact wording will vary from model to model.

Again, the wording will vary slightly depending on your exact router. Connect your other computers and devices to the router or hub. Your host and router have been configured, and now it's time to connect your other devices. If connecting via Ethernet, connect each additional computer to the LAN ports on the router or hub. If connecting wirelessly, connect to the router as if you were connecting to any wireless network. This is typically the case if you only have one network adapter installed.

You must have at least two different network adapters installed to use internet connection sharing. The other computers on the network are not getting an internet connection. This is typically caused by the computer not getting a correct IP address. Make sure that you only have internet connection sharing enabled on the host computer, and only on the adapter that's connected to the internet.

All of the other computers on the network should not have internet connection sharing enabled. Open the Network Connections window on the computer that cannot get an internet connection.

Right-click on the network adapter and select Properties. Select "Obtain IP address automatically". The other computers can share files but cannot connect to the internet. Bridging your two network adapters may help solve this problem. Select the two adapters that you want to bridge.

This should be the adapter that is connected to the internet and the adapter that is connected to the rest of the network. Hold Ctrl and click each one to select them.

Right-click on one of the two selected networks and select "Bridge Connections". Click Yes when prompted. Reboot the other computer and try connecting again. I'm receiving the "An error occurred while Internet Connection Sharing was being enabled. This can be caused by a problem with the internet sharing services in Windows. Press Enter to open the Services window. Find each of the following services: Reboot the computer after setting each service and try the connection again.

Follow the steps in the first section to enable internet connection sharing on the host computer. This method will allow you to use an unused wireless adapter on your Windows host computer to broadcast a wireless network that any other device can connect to, just like a wireless router.

First, you'll need to enable internet connection sharing on the host computer by following Steps of the first section. The host computer will need to have a wireless adapter that isn't being used in order to broadcast a signal for other computers and devices to connect to. If the host computer doesn't have a wireless card installed, you can use a USB wireless adapter.

Make sure you only enable internet connection sharing on the adapter that's connected to the internet. Don't enable internet sharing on the wireless adapter that you'll be using to create the wireless network.

This will open a new window with your active network connections. Select "Set up a new connection or network". Home or Work and Public. Only one profile can be active at a time. All the settings are the same and repeated under each profile. In Windows 8 and 10, you have three profiles: Private , Guest or Public and All Networks.

Network Discovery — This setting is turned on for private networks by default and it means that your computer can be seen by other computers and vice versa. What this means in practice is that when you open Windows Explorer, you might see the name of another computer connected to your network under Network Locations. File and Printer Sharing — This setting will allow others to access shared folders and printers on your computer.

I always turn this to Off even on private networks unless I need to use it in a specific situation. There are so many times when guests come over to my house, connect to the network and then could possibly browse my system. HomeGroup connections — If you really do need to share files and folders, you should just setup a HomeGroup , which is more secure and a lot easier to configure.

If you do run into trouble, just read my HomeGroup troubleshooting guide. There are a couple of more settings here. Public Folder Sharing — I recommend turning this off unless you specifically need to share data with another computer. A very useful feature when you need it, but a big privacy risk otherwise. Media Streaming — This is another option you should keep disabled until you need to use it. This basically turns your computer into a DLNA server so that you can stream music, movies and pictures to other devices on the network like an Xbox One, etc.

When enabled, it opens up quite a few ports in your firewall also. File Sharing Connections — This should always be set to Use bit encryption unless you need to share files with Windows 95, Windows 98 or Windows computers. Password Protected Sharing — I highly recommend turning on password protected sharing because it will force users to enter a username and password for an account on your computer in order to access any data. The next part I want to talk about is the section under Change your networking settings.

In Windows 10, you can either setup a new connection or troubleshoot problems. Note that creating an ad-hoc network is no longer possible in Windows These are not just troubleshooting guides, they are actual programs that run and fix issues with various networking related services. I have found the Internet Connections and Network Adapter troubleshooting fixes to be the most useful.

Here you will see a list of all the network adapters on your computer. You might also see other network adapters, but they are usually always virtual, meaning they are created by a software application like a VPN client or virtual machine program.

This will usually fix any problem with a misconfigured network adapter. If you right-click and choose Properties , you can configure your computer to use a static IP address rather than obtaining one from a DHCP server.

For the technically savvy, there are a lot of other advanced settings you can modify here, but this guide is meant for newbies. If you have any questions, post a comment. December 21st, by Aseem Kishore File in:

Opening Network & Sharing Center